I had 8 tall stems of leaves with golden berries that I had once used in a tall vase and I slipped them into the wreath forming a circle of leaves and berries all the way around. I secured them with my glue gun. I then added a few of the salvaged leaves, and a few bright orange berries that I had saved from another project, again using the glue gun to attach the items. The final touch was making a new bow from fall ribbon. After I attached the bow with wire, I added a few extra streamers, using the glue gun to hold the ribbon in place. The picture below is what I started with. The top picture is the finished product.
If you can make a decent bow, you can dress up the Christmas tree, make plain wreaths look beautiful and make inexpensive gifts look upscale. Bow making is awkward at first, but once you get the hang of it, you will be asked to make bows for everyone. I can't tell you how many bows I've made for people. It is easier to show someone how to do this than to tell them, but I'll try with the help of a few pictures my husband took last December. I'm sitting cross-legged on my couch, please ignore everything except the bow!
Get your "ingredients" ready. You will need ribbon (wire-edged works best), some fine wire (I have used extra pieces of ribbon, twist ties from bread, hair ties and rubber bands, but wire is best), and scissors. This is a roll of 5 yards of ribbon I picked up for a quarter after Christmas one year. You can make a bow with 3 yards, but I like to have at least 5 yards. If you are making huge bows, you will need more.
I am right handed, so I take the end of the ribbon and roll it to the back with my right hand, while holding the rest of the ribbon about 2 inches down in my left hand.
Make a complete loop and hold it tightly with your left thumb inside the loop and your other left fingers under the ribbon.
This step is very important. It is what makes a florist bow look good, and the ones we all make look slightly "off". Twist the ribbon behind the loop completely over. The above picture I'm starting to twist. When the twist is complete, grab it with those left fingers. Yes, your hand will be starting to cramp, it will get worse.
Above I am still holding the loop in my left hand, the ribbon has been twisted which keeps the pattern to the top and I'm starting my first bow loop with my right hand.
The loop is made by folding the ribbon under the piece extending from the small loop my thumb is holding, and you catch the underside of the loop with your fingers. See how tightly I'm holding it? The next picture is important!
We have made one loop of our bow, and we are holding it tightly in the left hand. Now we have to TWIST it again, completely over to bring the top/pattern of the ribbon to the top again.
After you twist the ribbon after the first loop, you make a loop on the opposite side the same way. Make the top of the loop, and fold the ribbon under and catch it with those left fingers.
Then you TWIST again, the secret is in the twist. and make another loop, grab it and twist until you have four loops on each side. You can make a bow with 3 loops per side, I think 4 looks better, but I have certainly made many bows with 3 loops each side. The more loops, the more full the bow. The bow on my fall wreath has 6 loops per side.
At this point there are 4 loops on each side of the bow.
Grab the tail of the ribbon that is still on the spool, and extend it as long as you want the streamers to be, then fold it up and bring the other end up to catch in your left hand. See above and below.
What you are seeing above is the back of the bow, held tightly in my left hand. The 8 loops are on the underside, the "tail" of the ribbon has been brought up into a loop of its own and I'm holding it in place. The ribbon that is left over that I'm going to cut off is extending to the right.
Take a piece of wire (8-10 inches) and bring it up through the streamer loop from back to front, insert it into that small center loop that was the first loop we made in picture number 1. See below.
This is where it is easy to lose the bow, so hang on tightly. The wire has to be twisted behind the small original loop and hold all of the bow loops in place as well as the streamer tails.
When it is twisted tightly and everything is in place, cut off the extra ribbon (still attached to the spool or lose if not on a spool. See below.
Next, you can either cut the streamer loop to have 2 streamers (cut on an angle) or you can leave it as a streamer loop for a different look.
Fluff up the loops, and you are done. This isn't my best, as I was posing for pictures rather than thinking about the bow, but you get the idea. Don't be discouraged if you let go and it all falls apart, just start over-wire ribbon is very forgiving. It takes a little practice to be comfortable with it.